10G BASE-T Copper SFP+ Transceiver JHA3901G

Short Description:

10GBASE-T Copper SFP+ Transceiver, 300m


Overview

Download

Features:                                              

◊ Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T

◊ Hot-pluggable SFP footprint

◊ Compact RJ-45 connector assembly

◊ RoHS compliant and lead-free

◊ Single +3.3V power supply

◊ 10 Gigabit Ethernet over Cat 6a cable

◊ Ambient Operating temperature: 0°C to +70°C

Applications:

◊ 10G Ethernet over Cat 5 cable

◊ Switch/Router to Switch/Router Link

◊ High speed I/O for file severs

Description:

JHA3901G SFP+-10GBASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP+-10GBASE-T uses the SFP’s RX_LOS(must be pulled up on host) pin for link indication. If pull up or open SFP’s TX_DISABLE pin,  PHY IC be reset.

• SFP to Host Connector Pin Out

Pin

Symbol

Name/Description

Ref.

1

VEET

Transmitter Ground  (Common with Receiver Ground)

1

2

TFAULT

Transmitter Fault. Not supported.

 

3

TDIS

Transmitter Disable. Laser output disabled on high or open.

2

4

MOD_DEF(2)

Module Definition 2. Data line for Serial ID.

3

5

MOD_DEF(1)

Module Definition 1. Clock line for Serial ID.

3

6

MOD_DEF(0)

Module Definition 0. Grounded within the module.

3

7

Rate Select

No connection required

 

8

LOS

High indicates no linked.  low indicates linked.

4

9

VEER Receiver Ground  (Common with Transmitter Ground)

1

10

VEER Receiver Ground  (Common with Transmitter Ground)

1

11

VEER Receiver Ground  (Common with Transmitter Ground)

1

12

RD-

Receiver Inverted DATA out.  AC Coupled

 

13

RD+

Receiver Non-inverted DATA out.  AC Coupled

 

14

VEER

Receiver Ground  (Common with Transmitter Ground)

1

15

VCCR

Receiver Power Supply

 

16

VCCT

Transmitter Power Supply

 

17

VEET

Transmitter Ground  (Common with Receiver Ground)

1

18

TD+

Transmitter Non-Inverted DATA in. AC Coupled.

 

19

TD-

Transmitter Inverted DATA in.  AC Coupled.

 

20

VEET

Transmitter Ground  (Common with Receiver Ground)

1

Notes:

1. Circuit ground is connected to chassis ground

2. PHY disabled on TDIS  > 2.0V or open, enabled on TDIS < 0.8V

3. Should be pulled up with 4.7k – 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.  

4. LVTTL compatible with a maximum voltage of 2.5V.  

4

Figure 1. Diagram of host board connector block pin numbers and names

• Cable Length

Standard

Cable

Reach

Host Port

10Gbase-T

CAT6A

30m

XFI

5Gbase-T/2.5Gbase-t

CAT5E

50m

5GBase-R/2.5GBase-X

1000base-T

CAT5E

100m

1000base-FX

• +3.3V Volt Electrical Power Interface

The JHA3901G SFP+-10GBASE-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation.

+3.3 Volt Electrical Power

Interface

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Supply Current

Is

 

700

900

mA

3.0W max power over

full range of voltage

and temperature.

See caution note below

Input Voltage

 Vcc

3.13

3.3

3.47

V

Referenced to GND

Maximum Voltage

Vmax

 

 

4

V

 

Surge Current

Isurge

 

TBD

 

mA

Hot plug above steady state

current.  See caution note

below


Caution: Power consumption and surge current are higher than the specified values in the SFP MSA

• Low-Speed Signals

MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals. Both MOD_ DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc.

Low-Speed Signals,  Electronic Characteristics

Parameter

Symbol

Min

Max

unit

Notes/Conditions

SFP Output LOW

VOL

0

0.5

V

 

4.7k to 10k pull-up to host_Vcc,

measured at host side of connector

SFP Output HIGH

VOH

host_Vcc -0.5

host_Vcc + 0.3

V

 

4.7k to 10k pull-up to host_Vcc,measured at host side of connector

SFP Input LOW

VIL

0

0.8

V

4.7k to 10k pull-up to Vcc,measured at SFP side of connector

 

SFP Input HIGH

VIH

2

Vcc + 0.3

V

4.7k to 10k pull-up to Vcc,

measured at SFP side of connector


• High-Speed Electrical Interface

All high-speed signals are AC-coupled internally.

High-Speed Electrical Interface,  Transmission Line-SFP

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Line Frequency

fL

 

125

 

MHz

5-level encoding, per

IEEE 802.3

Tx Output Impedance

Zout,TX

 

100

 

Ohm

Differential, for all

frequencies between

1MHz and 125MHz

Rx Input Impedance

Zin,RX

 

100

 

Ohm

Differential, for all

frequencies between

1MHz and 125MHz

 

High-Speed Electrical Interface,  Host-SFP

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Single ended data input

swing

Vinsing

250

 

1200

mV

 

Single ended

Single ended data output

swing

Voutsing

350

 

800

mV

Single ended

Rise/Fall Time

Tr,Tf

 

175

 

psec

20%-80%

Tx Input Impedance

Zin

 

50

 

Ohm

Single ended

Rx Output Impedance

Zout

 

50

 

Ohm

Single ended


• General Specifications

General

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Data Rate

BR

1

 

10

Gb/sec

IEEE 802.3 compatible.

See Notes 1,2 below

Notes:

  1. Clock tolerance is +/- 50 ppm

• Environmental Specifications

Automatic crossover detection is enabled.  External crossover cable is not required

Environmental

Specifications

 

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Operating Temperature

Top

0

 

65

°C

Case temperature

Storage Temperature

Tsto

-40

 

85

°C

Ambient temperature


• Serial Communication Protocol

All SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h.

Serial Bus Timing, Requirements

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

I 2C Clock Rate

 

0

 

200,000

Hz

 

• EEPROM INFORMATIONA2,optional

32

• Recommended Application Circuit

43

• Serial ID Memory Contents

Addr

Field Size

(Bytes)

Name of Field

HEX

Description

0

1

Identifier

03

SFP

1

1

Ext. Identifier

04

MOD4

2

1

Connector

22

RJ45

3-10

8

Transceiver

00 00 00 00 00 00 00 00

Transmitter Code

11

1

Encoding

06

64B66B

12

1

BR, nominal

67

10000M bps

13

1

Reserved

00

 

14

1

Length (9um)-km

00

 

15

1

Length (9um)

00

 

16

1

Length (50um)

00

 

17

1

Length (62.5um)

00

 

18

1

Length (copper)

1E

30m

19

1

Reserved

00

 

20-35

16

Vendor name

 JHA Technology Co., Ltd

 

36

1

Reserved

00

 

37-39

3

Vendor OUI

00 00 00

 

40-55

16

Vendor PN

JHA3901G

ASC II

56-59

4

Vendor rev

31 2E 30 20

V1.0

60-61

2

Wavelength

00 00

850nm

62

1

Reserved

00

 

63

1

CC BASE

XX

Check sum of byte 0~62

64-65

2

Options

00 1A

LOS, TX_DISABLE, TX_FAULT

66

1

BR, max

00

 

67

1

BR, min

00

 

68-83

16

Vendor SN

 

Unspecified

84-91

8

Vendor date code

XX XX XX 20

Year, Month, Day

92-94

3

Reserved

00

 

95

1

CC_EXT

XX

Check sum of byte 64~94

96-255

160

Vendor specific

 

 

• Mechanical Dimensions

 34

Mechanical Dimensions of Transceiver

JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information.

Published by Shenzhen JHA Technology Co., Ltd

Copyright © Shenzhen JHA Technology Co., Ltd

All Rights Reserved


  • Previous:
  • Next:

  • Write your message here and send it to us