Kūʻai kūʻai nui ʻo Kina Rs485 - Paʻa ʻia E1-FE mea hoʻololi JHA-CE1fF1 – JHA

E1-FE mea hoʻololi hoʻololi JHA-CE1fF1

Nānā nui

Hoʻokumu ʻia kēia mea hoʻololi hoʻololi ma FPGA, e hāʻawi ana i hoʻokahi kikowaena E1 i hoʻopaʻa ʻia a me hoʻokahi interface Ethernet e hoʻokō ai i ka hoʻoili ʻikepili 10/100Base-T Ethernet ma ke kahawai E1. He hana kiʻekiʻe, aʻo ponoʻī Ethernet alahaka. ʻO kēia hāmeʻa ka mea hoʻonui o Ethernet, me ka hoʻohana ʻana i ka pūnaewele (PDH/SDH/Microwave) e hāʻawi i ke ala E1 e hoʻokō ai i ka Ethernet kūloko a mamao hoʻi e pili ana me nā kikowaena serial ma ke kumu kūʻai haʻahaʻa. Loaʻa i ka polokalamu ka hana hoʻāʻo loop inter-set e hoʻomaʻamaʻa i ka hoʻomaka ʻana o ka papahana a me ka mālama ʻana i kēlā me kēia lā.

Kiʻi Huahana

ʻAno Mini

Nā hiʻohiʻona

• Ma muli o ka IC pono'ī
• Hiki ke hoʻomaopopo i ka nānā ʻana a me ka mālama ʻana i nā lako mamao, ʻaʻole i lawe ka ʻikepili hoʻokele OAM i ka manawa o ka mea hoʻohana a mālama i ka bandwidth E1
• Kākoʻo ʻo E1 i kēlā me kēia hoʻonohonoho timeslot, ʻo ka helu he 64K-2048K
• Hiki i ka mea kūloko ke hoʻoikaika i ka helu kelepona mamao e hahai iā ia
• Loaʻa i ka hana o ka E1 interface loop back check, e pale aku i ka converter crashed no ka hoʻi ʻana o ka loop loop;
• Loaʻa ka hōʻailona i ka wā e pau ai ka mana a i ʻole ka laina E1 i haki a nalowale paha i ka hōʻailona;
• Hiki iā ia ke hoʻonohonoho i ka laina E1 e hoʻouna ʻole i ka hōʻailona LINK i ka interface Ethernet i ka wā e haki ai ka laina E1;
• Kākoʻo ke kikowaena Ethernet i nā papa jumbo (2036 Bytes);
• Inter-set dynamic Ethernet MAC address (4,096) me ka kānana ʻikepili kūloko
• Kākoʻo ʻo Ethernet i ka 10M/100M, hapalua/full duplex auto- Negotination a me AUTO-MDIX (laina kea a me ka laina pili pololei i hiki ke hoʻololi iā ia iho);
• Loaʻa iā Ethernet ka hana hoʻoponopono hou iā ia iho, ʻaʻole e make nā mea hana
• Hiki iā ʻoe ke hoʻokō i ka hoʻonohonoho ʻana o ka mea mamao i kēlā me kēia mode 5 o Ethernet a hiki ke pani i ka hana AUTO-MDIX;
• Hāʻawi i 2 mau ʻano uaki: E1 master clock a me E1 line clock;
• Loaʻa i ʻekolu ʻano Loop Back: E1 interface Loop Back (ANA)、Pilikia Ethernet Loop Back(DIG)、Kauoha i ka mamao
• Pilikia Ethernet Loop Back(REM)
• Hāʻawi i 2 impedances: 75 Ohm unbalance a me 120 Ohm kaulike;
• Kākoʻo SNMP Network Management;
• Hiki ke ʻike i ka nānā ʻana i ka mahana o nā lako mamao a me ka volta mai nā lako kūloko;
• Hiki ke hana i ka hale: Ethernet E1 Bridge(A)－－-E1 Optical Fiber Modem (B)－－-Ethernet Optical Fiber Modem (C)
• Hiki ke hana i ka hale: Ethernet E1 Bridge(A)－－-Optical Ethernet E1 Alahaka (B)－－-Ethernet Optical Fiber Transceiver (C), hiki ke hoʻokele (B) a me (C) ma (A)

Nā ʻāpana

♦E1 Interface

Kūlana Interface: hoʻokō me ka protocol G.703;
Ka helu o ka Interface: n*64Kbps±50ppm;
Code Interface: HDB3;

E1 Impedance: 75Ω (ke kaulikeʻole), 120Ω (kaulike);

ʻO ka hoʻomanawanui Jitter: E like me ka protocol G.742 a me G.823

ʻAe ʻia ka Attenuation: 0~6dBm

♦Pākuʻi Ethernet(10/100M)

Laki waena: 10/100 Mbps, ka hapalua/ piha duplex auto-negotiation

Kūlana Interface: Kūpono me IEEE 802.3, IEEE 802.1Q (VLAN)

Hiki iā MAC Address: 4096

Mea hoʻohui: RJ45, kākoʻo Auto-MDIX

♦Kaiapuni hana

Ka wela hana: -10°C ~ 50°C

Ka haʻahaʻa hana: 5% ~ 95 % (ʻaʻohe condensation)

Ka mahana mālama: -40°C ~ 80°C

Waihona haʻahaʻa: 5%~95 % (ʻaʻohe condensation)

Nā kikoʻī

Palapala noi

Haʻina maʻamau 1

Haʻina maʻamau 2

Haʻina maʻamau 3