Fiber-4Voice +4FE Multiplexer JHA-P04FE04 Overview Hāʻawi kēia hāmeʻa i ke kelepona 1-4Channel, 4Channel 10M/100M Ethernet interface (Wire Speed ​​100M), ʻo 4Channel Ethernet interface ka mea hoʻololi. ʻO ka mīkini holoʻokoʻa e hana hilinaʻi a paʻa me ka hoʻohana haʻahaʻa haʻahaʻa, ka hoʻohui kiʻekiʻe, ka liʻiliʻi liʻiliʻi a me ka hoʻonohonoho maʻalahi a me ka mālama. Nā hiʻohiʻona ʻano kiʻi liʻiliʻi ma muli o ka IC ponoʻī; Hiki i ka hopena kūloko ke hōʻike i ke kūlana pili fiber o ka mea mamao; Kākoʻo ke awa leo i ke awa FXO a me FXS, Kākoʻo iā FXO/FXS, Kelepona kelepona Magnet, FXO port docking me ka papahana-controlled switchboard , FXS awa pili i ke kelepona o ka mea hoʻohana;; 1 ~ 4channel komo leo, Voice FXO / FXS interface, kākoʻo no ka mea kelepona ID / hoʻohuli i ka polarity billing / hana fax; ； Kākoʻo i nā wahi like ʻole i ka hana hoʻokaʻawale helu; Hiki i ka Ethernet interface ke kākoʻo iā AUTO-MDIX (laina kea a me ka laina pololei i hoʻopili pono ʻia. )； AC220/5-12V mana hoʻololi, hiki ke hoʻololi i ka mana DC-48V/5-12V waho; Kelepona kaʻana like me ka pale uila, hiki i ka uila i IEC61000-4-5 Pōkole kaapuni o kēia manawa nalu 10 / 700μs, ka peak output voltage 6KV open standards. ♦ Fiber Multi-mode Fiber 50 / 125um, 62.5 / 125um, Ka mamao hoʻouna kiʻekiʻe: 5Km @ 62.5 / 125um hoʻokahi fiber mode, attenuation (3dbm / km) Ka lōʻihi o ka hawewe: 850nm / 1310nm Ka mana hoʻouna: -12dBm -12dBm. (Max) Loaʻa sensitivity: -28dBm (Min) Link budget: 16dBm Single-mode Fiber 8/125um, 9/125um Ka lōʻihi o ka hoʻouna ʻana: 120Km Ka lōʻihi o ka lawe ʻana: 20~120Km @ 9 / 125um hoʻokahi ʻano fiber, attenuation (0.35dbm/km) : 1310nm Ka mana hoʻouna: -9dBm (Min) ~-8dBm (Max) ʻO ka ʻike o ka mea loaʻa: -27dBm (Min) Hoʻohui kālā: 18dBm ♦ E1 Interface Interface Standard: e hoʻokō me ka protocol G.703; Ka helu o ka Interface: n*64Kbps±50ppm; Code Interface: HDB3; E1 Impedance: 75Ω (ke kaulikeʻole), 120Ω (kaulike); ʻO ka hoʻomanawanui Jitter: E like me ka protocol G.742 a me G.823 i ʻae ʻia Attenuation: 0~6dBm ♦ Ethernet interface(10/100M) Interface rate: 10/100 Mbps, half/full duplex auto-negotiation Interface Standard: Compatible me IEEE 802.3 , IEEE 802.1Q (VLAN) Hiki i ka helu wahi MAC: 4096 Mea Hoʻohui: RJ45, kākoʻo Auto-MDIX ♦ FXS Phone Interface Ring voltage: 75V Ring frequency: 25HZ Two-line Impedance: 600 Ohm (pick up) Return loss: 40 dB ♦ FXO Switch Interface Ring e ʻike i ka volta: 35V Ring detection frequency: 17HZ-60HZ ʻElua-laina Impedance: 600 Ohm (kiʻi i luna) Hoʻihoʻi poho: 40 dB Hoʻihoʻi nalowale: 20 dB ♦ Kaiapuni hana Ka mahana hana: -10°C ~ 50°C Haʻahaʻa hana: 5%~95 % (ʻaʻohe condensation) Ka mahana mālama: -40°C ~ 80° C Waihona Haʻahaʻa: 5%~95 % (ʻaʻohe condensation) Ke Ana Hoʻohālike JHA-P04FE04 Hōʻike Hana 4* kelepona，4*100 Mbps Ethernet，1* Fiber interface Ka mana lako: DC5-12V Mana hoʻohana: ≤10W Ana Nui Huahana: 216X140X31mm(WXDXH) ʻano mini Kaumaha 1KG Noi

Hoʻokaʻawale ʻo G.703 (Co-Directional G.703) i ka pōʻaiapuni 64Kbps i 4 ʻāpana, hoʻohana ʻo ia i ka "0101" e hōʻike ana i "0", "1100" e hōʻike ana i "1". Hoʻololi nā hōʻailona i nā hōʻailona pae ʻekolu I kēlā me kēia hui 8 i luku ʻia ka poloka o ka polarity ʻokoʻa, no laila e hoʻouna i ka manawa 8KHz ʻO ka hōʻailona ma luna, G.703 co-directional 64Kbps hōʻailona hiki ke hoʻokō i ka hoʻouna ʻana i ka hōʻailona manawa o 64KHz a me 8KHz a me 64KHz a me ka hōʻailona ʻikepili o 64Kbit/s ma ka ʻaoʻao like me kahi laina kaulike ʻelua ʻO ke kuhi kuhikuhi G.703 a me hoʻokahi pānaehana Ethernet e hoʻokō i ka hoʻoili ʻikepili 10/100Base-T Ethernet ma ka ʻO G.703 kahi alahaka Ethernet aʻo ponoʻī ʻo ia ka mea hoʻonui o Ethernet, me ka hoʻohana ʻana i ka pūnaewele (PDH/SDH/Microwave) e hoʻolako i ke kahawai G.703 e hoʻokō i ka Ethernet kūloko a me ka serial. ʻO ke kumu kūʻai haʻahaʻa he hana hoʻāʻo loop inter-set e hoʻomaʻamaʻa i ka hoʻomaka ʻana o ka papahana a me ka mālama ʻana i kēlā me kēia lā. Huahana Photo Mini Type Hiʻona Ma muli o ka pono kope IC Hiki ke hoʻomaopopo i ka lawe ʻana i ka ʻikepili Ethernet i hoʻokahi kaapuni Co-directional G.703 Inter-set dynamic Ethernet MAC address (4,096) me ke kānana ʻikepili kūloko Hiki i ka mea kūloko ke hoʻokele i ka mea mamao Loaʻa ka hana o G.703 loop hope nānā, a kuhikuhi ma LED Hiki ke hoʻokaʻawale i ke kumu o Co-directional G.703 nalowale hōʻailona mea i ka mamao mea mana-off a kuhikuhi G.703 laina wawahi Ethernet. Kākoʻo ka interface i ka 10M/100M, hapalua/full duplex auto- adaptable, kākoʻo VLAN Ethernet interface kākoʻo AUTO-MDIX (kea laina a me straightly hono laina pono-adaptable); Hāʻawi i 2 ʻano uaki: Co-Directional G.703 master clock a me G.703 line clock; Hiki i ka mea kūloko ke hoʻoikaika i ka helu kelepona mamao e hahai iā ia (inā ʻaʻole i hoʻopaʻa ʻia ka hāmeʻa, ʻaʻole kūpono ia) Loaʻa ʻekolu Loop Back Mode: G.703 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、E kauoha i ka mamao. Hoʻopili ʻo Ethernet Loop Back (REM) Kākoʻo iā ia iho i ke kaulike 120 Ohm; Nā ʻāpana ♦ Co-Directional G.703 Interface Interface Standard: e hoʻokō me ka protocol ITU-T G.703; Kikowaena Interface: 64Kbps±50ppm; E1 Impedance: 120Ω (kaulike); ʻO ka hoʻomanawanui Jitter: E like me ka protocol G.742 a me G.823 Ka lōʻihi o ka hoʻouna ʻana i ka mamao: a hiki i 500m ♦ Ethernet interface (10/100M) Laki waena: 10/100 Mbps, hapalua/full duplex auto-negotiation Interface Standard: Compatible me IEEE 802.3, IEEE 802.1Q (VLAN) Hiki i ka helu wahi MAC: 4096 Mea hoʻohui: RJ45, kākoʻo Auto-MDIX ♦ Kaiapuni hana Ka mahana hana: -10 ° C ~ 50 ° C Ka haʻahaʻa hana: 5% ~ 95 % (ʻaʻohe condensation) Ka mahana mālama: -40 ° C ~ 80 ° C Waihona Humidity: 5 %~95 % (ʻaʻohe condensation) Nā mea kiko'ī Helu kumu hoʻohālike:JHA-CE1tF1 Hōʻike Hana 10 / 100M Ethernet kaila hoʻouna ʻikepili ma ka ʻaoʻao like ma ka G.703 (Co-Directional G.703), Ethernet rate 64K Port Description Hoʻokahi hui kuhikuhi 64K interface, 1 Fast Ethernet interface Mana Mana: AC180V ~ 260V;DC –48V ；DC +24VPo ka mana: ≤10W Ana Nui Huahana: 216X140X31mm (WXDXH) Kaumaha 1.2KG Noi

Nā hiʻohiʻona: ♦ 4 kūʻokoʻa kūʻokoʻa piha-duplex ♦ A hiki i 11.2Gbps no kēlā me kēia channel bandwidth ♦ Agregate bandwidth o > 40Gbps ♦ MTP/MPO optical connector ♦ QSFP MSA compliant ♦ Digital diagnostic capabilities ♦ Hiki ke hoʻouna ʻia ma luna o 300mmode Fiber (300mF) a 150m ma luna OM4 MMF ♦ CML pili uila I/O ♦ Hoʻokahi + 3.3V mana lako hana ♦ TX hoʻokomo a me RX puka CDR hoʻomaha ♦ Nā hana diagnostic kikohoʻe i kūkulu ʻia ♦ Ka wela wela 0 ° C a 70 ° C ♦ RoHS Compliant Part Applications: ♦ Rack e hoʻopaʻa ♦ Nā kikowaena ʻikepili ♦ Nā pūnaewele Metro ♦ Nā Hoʻololi a me nā Router ♦ Infiniband 4x SDR, DDR, QDR Hōʻike: ʻO ka JHA-QC01 he 40Gbps Quad Small Form-factor Pluggable (QSFP) optical module e hāʻawi ana i ka hoʻonui ʻia o ka port density a me ka nui o ka mālama kālā ʻana o ka ʻōnaehana. Hāʻawi ka QSFP full-duplex optical module i ka 4 kūʻokoʻa e hoʻouna a loaʻa i nā kahawai, hiki i kēlā me kēia mea ke hana 10Gbps no ka bandwidth aggregate o 40Gbps 300m ma OM3 Multimode Fiber (MMF) a me 400m ma OM4 MMF. Hoʻopili ʻia kahi kaula lipine fiber optical me kahi mea hoʻohui MPO/MTP ma kēlā me kēia hopena i loko o ka pahu kōpana QSFP. ʻO ka hoʻonohonoho ʻana o ke kaula lipine ʻo ia ka "ki" a aia nā pine alakaʻi i loko o ka pahu o ka module e hōʻoia i ka alignment kūpono. ʻAʻohe wili maʻamau o ke kaula (kī a hiki i ke kī i luna) no ka hōʻoia ʻana i ke kahawai kūpono i ka hoʻopololei ʻana. Loaʻa ka pilina uila me ka mea hoʻohui 38-pin IPASS® z-pluggable. Hoʻohana ka module mai kahi mana + 3.3V hoʻokahi a me nā hōʻailona mana honua LVCMOS/LVTTL e like me Module Present, Reset, Interrupt and Low Power Mode i loaʻa me nā modula. Loaʻa kahi interface serial 2-wire e hoʻouna a loaʻa i nā hōʻailona mana paʻakikī a loaʻa ka ʻike diagnostic diagnostic. Hiki ke kamaʻilio ʻia nā kaha pākahi a hiki ke pani ʻia nā kahawai i hoʻohana ʻole ʻia no ka maʻalahi o ka hoʻolālā. Hoʻolālā ʻia ka JHA-QC01 me ke ʻano kumu, ka pilina optical/electrical a me ke kikowaena diagnostic digital e like me ka QSFP Multi-Source Agreement (MSA). Ua hoʻolālā ʻia e hālāwai me nā kūlana hana ʻoi loa o waho e pili ana i ka mahana, ka haʻahaʻa a me ka hoʻopili EMI. Hāʻawi ka module i ka hana kiʻekiʻe loa a me ka hoʻohui ʻana i nā hiʻohiʻona, hiki ke loaʻa ma o kahi interface serial ʻelua-wire. l Hōʻailona Kūlana Kiʻekiʻe Loa Loaʻa Min. Max maʻamau. Wehehana Waihona Unite TS -40 +85 °C Voltage Voltage VCCT, R -0.5 4 V Hoʻohaʻahaʻa Pili RH 0 85 % • Kaiapuni Hana Manaʻo: Parameter Symbol Min. Max maʻamau. Huina hihia wela wela TC 0 +70 °C Voltage Hāʻawi VCCT, R +3.13 3.3 +3.47 V Hāʻawi i kēia manawa ICC 1000 mA Hoʻoheheʻe Mana PD 3.5 W • Nā ʻano uila (TOP = 0 a 70 °C, VCC = 3.13 a 3.47 Volts Parameter ʻO ka hōʻailona Min Typ Max Unit Note Ka helu ʻikepili no kēlā me kēia Kanal - 10.3125 11.2 Gbps mana hoʻohana - 2.5 3.5 W Hāʻawi i kēia manawa Icc 0.75 1.0 A Mana I/O Voltage-Kiʻekiʻe VIH 2.0 Vcc V Mana I/O Voltage-Haʻahaʻa VIL 0 0.7 V Inter-Channel Skew TSK 150L Ka lōʻihi P. - hōʻoia i ka manawa 100 ms Mana i ka manawa 100 ms Transmitter Hoʻokahi i hoʻopau ʻia ʻO ka Voltage Voltage Tolerance 0.3 4 V 1 mode maʻamau Ka hoʻomanawanui Voltage 15 mV Hoʻouna i ka hoʻokomo ʻokoʻa ʻokoʻa VI 120 1200 mV Hoʻouna i ka hoʻokomo ʻokoʻa impedance ZIN 80 100 120 ʻIkepili Jitter UI ʻIke TJ 0.28 UI Loaʻa Hoʻokahi Hoʻopau Voltage Voltage Tolerance 0.3 4 V Rx Output Diff Voltage Vo 600 800 mV Rx Output Piʻi a hāʻule Voltage Tr/Tf 35 ps 1 Huina Jitter TJ 0.7 UI Deterministic Jitter UI ～ 0.8% UI Optical Jitter UI DJ 0.82% Nā ʻāpana (TOP = 0 a 70 °C, VCC = 3.0 a 3.6 Volts) Hōʻailona Kūlana Min Typ Max Unit Ref. Ka lōʻihi o ka hawewe opi λ 840 860 nm RMS ka laula o ke kiʻekiʻe Pm 0.5 0.65 nm ka mana maʻamau no kēlā me kēia Channel Pavg -8 -2.5 +1.0 dBm Laser Off Power no kēlā me kēia Channel Poff -30 dBm Optical Extinction Ratio ER 3.5 dB Relative Rintensity / 12 dB Relative Intensity. HZ 1 Optical Hoʻihoʻi Pohō Hoʻomanawanui 12 dB Loaʻa Optical Center Wavelong λC 840 860 nm Mea Loaʻa Naʻauao ma kēlā me kēia Kanal R -13 dBm ʻO ka mana hoʻokomo kiʻekiʻe PMAX +0.5 dBm Receiver Reflectance Rrx -12 dB LOS De-Assert LOSD -14 dBm LOS0 dB5. dB Nānā 12dB Reflection • Loaʻa ka hana nānā diagnostics kikohoʻe ma nā QSFP+ SR4 a pau. Hāʻawi ka 2-wire serial interface i ka mea hoʻohana e launa pū me ka module. Hōʻike ʻia ke ʻano o ka hoʻomanaʻo i ke kahe. Hoʻonohonoho ʻia ka wahi hoʻomanaʻo i loko o kahi ʻaoʻao haʻahaʻa, hoʻokahi ʻaoʻao, wahi kikoʻī o 128 bytes a me nā ʻaoʻao kikowaena helu luna. Hāʻawi kēia ʻano i ka hiki i ka manawa kūpono i nā helu ma ka ʻaoʻao haʻahaʻa, e like me Interrupt Flags and Monitors. Loaʻa nā mea kākau manawa koʻikoʻi liʻiliʻi, e like me ka ʻike serial ID a me nā hoʻonohonoho paepae, me ka hana ʻAoʻao Select. ʻO A0xh ka leka uila i hoʻohana ʻia a hoʻohana nui ʻia no ka ʻikepili koʻikoʻi o ka manawa e like me ka lawelawe interrupt i mea e hiki ai i ka heluhelu hoʻokahi manawa no nā ʻikepili āpau e pili ana i kahi kūlana keakea. Ma hope o ka hoʻopaʻapaʻa ʻana, IntL, hiki i ka mea hoʻokipa ke heluhelu i ke kahua hae e hoʻoholo ai i ke kahawai pili a me ke ʻano o ka hae. ʻO ka Page02 ka mea hoʻohana EEPROM a ua hoʻoholo ʻia e ka mea hoʻohana. E ʻoluʻolu e ʻike i ka palapala SFF-8436 ka wehewehe kikoʻī o ka hoʻomanaʻo haʻahaʻa a me ka page00.page03. • Ka manawa no ka Mana Mana a me ke kūlana o ka hana Parameter Symbol Max Unit Conditions Initialization Time t_init 2000 ms Ka manawa mai ka mana on1, wela wela a i ʻole ka piʻi ʻana o ka ʻaoʻao o Reset a hiki i ka holo pono ʻana o ka module. ʻoi aku ka lōʻihi ma mua o ka liʻiliʻi o ka manawa pulse hōʻano hou ma ka pine ResetL. Manawa Mākaukau Lako Bus Serial t_serial 2000 ms Ka manawa mai ka mana on1 a hiki i ka pane ʻana o ka module i ka hoʻouna ʻana i ka ʻikepili ma luna o ke kaʻaahi serial 2-wire Nānā Ikepili Manawa t_data 2000 ms Manawa mai ka mana ma1 a hiki i ka ʻikepili ʻaʻole i mākaukau, bit 0 o Byte 2, deasserted a ʻōlelo ʻia ʻo IntL Hoʻihoʻi hou i ka Manawa Manaʻo t_reset 2000 ms Ka manawa mai ka piʻi ʻana ma ka pine ResetL a hiki i ka piha ʻana o ka module functional2 LPMode Assert Time ton_LPMode 100 μs Ka manawa mai ka hoʻohiki ʻana o LPMode (Vin:LPMode =Vih) a hiki i ka komo ʻana o ka mana o ka module i lalo Mana Level IntL Assert Time ton_IntL 200 ms Ka manawa mai ka hiki ʻana mai o ke kūlana e hoʻomaka ana IntL a hiki i Vout:IntL = Vol IntL DeastL Time 500 μs toff_IntL 500 μs Manawa mai ka maopopo ma ka heluhelu 3 ka hana o ka hae pili a hiki i ka Vout:IntL = Voh. Hoʻopili kēia i nā manawa deassert no Rx LOS, Tx Fault a me nā ʻāpana hae ʻē aʻe. Rx LOS Assert Time ton_los 100 ms Manawa mai Rx LOS mokuʻāina i Rx LOS bit set a IntL asserted Flag Assert Time ton_flag 200 ms Manawa mai ka hiki ʻana mai o ke kūlana e hoʻoulu ana i ka hae i ka hoʻonohonoho bit hae pili a ua hoʻokūpaʻa ʻia ʻo IntL Mask Assert Time ton_mask 100 ms Ka manawa mai ka mask. bit set4 a hiki i ka wā e pale ʻia ai ka ʻōlelo IntL pili i ka Mask De-assert Time toff_mask 100 ms Hoʻomaʻemaʻe ʻia ka manawa mai ka bit mask 4 a hiki i ka hoʻomaka ʻana o ka hana IntlL pili i ka ModSelL Assert Time ton_ModSelL 100 μs Manawa mai ka ʻōlelo ʻana o ModSelL a hiki i ka pane ʻana o ka module i ka lawe ʻana i ka ʻikepili ma luna o ke kaʻaahi serial 2-wire ModSelL Deassert Time toff_ModSelL 100 mau minuke o ka manawa mai ModSelL ʻAʻole pane ka module i ka lawe ʻana i ka ʻikepili ma luna o ka 2-wire serial bus Power_over-ride a i ʻole Power-set Assert Time ton_Pdown 100 ms Manawa mai P_Down bit set 4 a hiki i ka hoʻohana ʻana i ka mana module e komo i lalo Power Level Power_over-ride a i ʻole Power-set De-assert Time toff_Pdown 300 ms manawa mai P_Down bit i hoʻomaʻemaʻe ʻia4 a hiki i Ua holo pono ka module3 Nānā: 1. Ua wehewehe ʻia ka mana e like me ka manawa e hiki ai nā volta hoʻolako a noho ma luna a i ʻole ka palena iki. waiwai i kuhikuhi ʻia. 2. Ua wehewehe ʻia ka hana piha e like me ka IntL i ʻōlelo ʻia ma muli o ka ʻikepili ʻaʻole mākaukau bit, bit 0 byte 2 de-asserted. 3. Ana ʻia mai ka hāʻule ʻana o ka uaki ma hope o ka pau ʻana o ka heluhelu heluhelu. 4. Ana ʻia mai ka hāʻule ʻana o ka uaki ma hope o ka pau ʻana o ka hana kākau. • Kiʻi Paʻi Paʻa Transceiver Kiʻi 1: Kiʻi Paʻi • Kiʻi Hoʻokaʻina Pin o ka Mea Hoʻohui Papa Hoʻokipa Block Nā helu Pin a me ka inoa • Hōʻike Pin Pin Logic Symbol Name/Description Ref. 1 GND Ground 1 2 CML-I Tx2n Transmitter Inverted Data Input 3 CML-I Tx2p Transmitter Non-Inverted Data Output 4 GND Ground 1 5 CML-I Tx4n Transmitter Inverted Data Input 6 CML-I Tx4p Transmitter Non-Inverted Data Output 7 Ka Honua 1 8 LVTTL-I ModSelL Module E koho i 9 LVTTL-I ResetL Module Reset 10 VccRx +3.3V Mea Loaʻa Mana Mana 2 11 LVCMOS-I/O SCL 2-Wire Serial Interface Clock 12 LVCMOS-I/O SDA 2-Wire Serial Interface Data 13 GND Ground 1 14 CML- O Rx3p Mea Loaʻa Hoʻohuli Ike ʻIkepili 15 CML-O Rx3n Receiver Non-Inverted Data Output 16 GND Ground 1 17 CML-O Rx1p Receiver Inverted Data Output 18 CML-O Rx1n Receiver Non-Inverted Data Output 19 GND Ground 1 20 GND Ground 1 21 CML-O Rx2n Receiver -O Rx2p Receiver Non-Inverted Data Output 23 GND Ground 1 24 CML-O Rx4n Receiver Inverted Data Output 25 CML-O Rx4p Receiver Non-Inverted Data Output 26 GND Ground 1 27 LVTTL-O ModPrsL LVT Interrupt in 28 LVT Module Present 28 +3.3V Mea Hoʻokuʻu Mana Mana 2 30 Vcc1 +3.3V Mana Mana 2 31 LVTTL-I LPMode Mana Haʻahaʻa Mana Haʻahaʻa 32 GND Ground 1 33 CML-I Tx3p Transmitter Huli ʻIkepili Huli 34 CML-I Tx3n Transmitter Non-Inverted GND ʻIkepili 35 1 36 CML-I Tx1p Mea lawe Hoʻopuka ʻIkepili Huli 37 CML-I Tx1n Transmitter Non-Inverted Data Output 38 GND Ground 1 Notes: ʻO GND ka hōʻailona no ka hoʻokahi a me ka lako (mana) maʻamau no nā modula QSFP, He mea maʻamau nā mea a pau i loko o ka module QSFP a ua kuhikuhi ʻia nā voltage module a pau. ʻike ʻia kēia hiki. E hoʻopili pololei i kēia mau mea i ka hōʻailona papa hoʻokipa i ka mokulele honua maʻamau. Hoʻopau ʻia ka hoʻopuka laser ma TDIS >2.0V a i ʻole wehe ʻia, hiki iā TDIS