Fiber-4Voice +GE Multiplexer JHA-P04GE01 Overview Sesebediswa sena se fana ka 1-4Channel mohala, 2Channel 10M/100M/1000M Ethernet interface (Wire Speed ​​100M)，1Channel Ethernet interface ke switch interface, e ka tšehetsa VLAN. Likarolo tsa Mofuta o Monyane oa Photo E ipapisitse le "copyright" ea IC; Qetello ea lehae e ka bonts'a boemo ba khokahano ea fiber ea sesebelisoa se hole; Voice port e ts'ehetsa FXO le FXS port, Support FXO/FXS, Magnet phone Interface, FXO port docking e nang le switchboard e laoloang ke lenaneo. , boema-kepe ba FXS bo hokahaneng le mohala oa mosebelisi; 1 ~ 4channel phihlello ea lentsoe, sebopeho sa Voice FXO / FXS, ts'ehetso bakeng sa mohalaleli oa ID / reverse polarity billing / fex; ； Ts'ehetsa libaka tse fapaneng tsa kabo ea linomoro tse fapaneng; Sehokelo sa Ethernet se ka tšehetsa AUTO-MDIX (mohala o tšetseng le mohala o hokahantsoeng ka kotloloho o ikamahanya le maemo. ) Adapter ea matla ea kantle ea AC220/5-12V, e ka boela ea ba adaptara ea motlakase ea kantle ea DC-48V/5-12V; Sehokelo sa mohala se nang le lehalima tshireletso, lehalima fihla IEC61000-4-5 Short potoloho jwale leqhubu 8 / 20μs, tlhōrō dipholo tsa gagamalo 6KV maemo a bulehileng. Mekhahlelo ♦ Fiber Multi-mode Fiber 50/125um, 62.5/125um, Boholo ba phetisetso sebaka: 5Km @ 62.5 / 125um single mode fiber, attenuation (3dbm/km) Bolelele ba Leqhubu: 820nm Matla a ho fetisa: -120m (MiBnm) ~9 Max) Moamoheli kutlo: -28dBm (Min) Budget ea khokahano: 16dBm Single-mode Fiber 8/125um, 9/125um Bolelele ba phetisetso e kholo: 40Km Sebaka sa phetisetso: 40Km @ 9 / 125um fiber e le 'ngoe, attenuation (0.35dbm/km:011 Leng) Wave Leng3 Matla a ho fetisa: -9dBm (Min) ~-8dBm (Max) Kutloisiso ea Moamoheli: -27dBm (Min) Tekanyetso ea khokahano: 18dBm ♦ E1 Interface Interface Standard: lumellana le protocol G.703; Interface Rate: n * 64Kbps ± 50ppm; Khoutu ea Sehokelo: HDB3; Tšitiso ea E1: 75Ω (ho se leka-lekane), 120Ω (ho leka-lekana); Mamello ea Jitter: Ho ea ka protocol G.742 le G.823 Attenuation e lumelletsoeng: 0~6dBm ♦ Ethernet interface(10/100/1000M) Interface rate: 10/100/1000 Mbps, half/full duplex auto-negotiation Interface Standard: E lumellana le IEEE 802.3, IEEE 802.1Q (VLAN) Aterese ea MAC Bokhoni: 4096 Connector: RJ45, tšehetsa Auto-MDIX ♦ FXS Phone Interface Ring voltage: 75V Ring frequency: 25HZ Impedance ea Mehala e 'meli: 600 Ohm (ho nka) Tahlehelo ea ho khutlisa: 40 dB Switch Interface ♦ Mohala oa ho lemoha matla: 35V maqhubu a ho lemoha a ring: 17HZ-60HZ Mela e 'meli Impedance: 600 Ohm (ho nka) Tahlehelo ea ho khutla: 40 dB Tahlehelo ea ho khutlisa: 20 dB ♦ Tikoloho ea ho sebetsa Mocheso oa ho sebetsa: -10 ° C ~ 50 ° C Mongobo o sebetsang: 5% ~ 95 % (ha ho condensation) Mocheso oa polokelo: -40°C ~ 80°C Mongobo oa polokelo: 5%~95 % (ha ho condensation) Specifications Model JHA-P04GE01 Tlhaloso ea Ts'ebetso 4* mohala，1*1000 Mbps Ethernet，1* Fiber interface Phepelo ea matla: DC5-12VPower tshebediso: ≤10W Dimension Saese ea Sehlahisoa: 90X104X31mm) mini (WXDXH) mofuta Weight 0.6KG Kopo

E1-8 Channel RS232/RS422/RS485 Converter JHA-CE1D8/R8/Q8 Overview Mofetoleli ona oa sehokelo o ipapisitse le FPGA, o fana ka phetiso ea 8Channel RS232/485/422 ho sebopeho sa E1. Sehlahisoa se senya likhohlano lipakeng tsa sebaka sa puisano sa serial interface le sekhahla sa puisano, ntle le moo, se ka rarolla tšitiso ea motlakase, tšitiso ea lesale la fatše le tšenyo ea lehalima. Sesebelisoa se ntlafatsa haholo ts'epo, ts'ireletso le lekunutu la puisano ea data. E sebelisoa haholo bakeng sa taolo ea liindasteri tse fapaneng, taolo ea ts'ebetso le linako tsa taolo ea sephethephethe, haholo bakeng sa Banka, le Matla le likarolo tse ling le litsamaiso tse nang le litlhoko tse ikhethang tsa tikoloho ea tšitiso ea motlakase. Seteishene sa RS232/RS485/RS422 se ka fetisetsa data ea serial e feto-fetohang ka mokhoa o tšoanang 0Kbps-57600Kbps sekhahla sa baud. Sehlahisoa Photo Mini mofuta oa 19inch 1U Mofuta oa Likarolo Ho ipapisitsoe le boits'oaro ba IC Support 3 line RS232 (TXD,RXD,GND), tšehetso bakeng sa taolo ea phallo CD,DSR,CTS Na le tse tharo Loop Back Mode: E1 interface Loop Back (ANA)、RS232 /485/422 segokanyimmediamentsi sa sebolokigolo Loop Back(DIG)、Laela RS232/485/422 segokanyimmediamentsi sa sebolokigolo Loop Back(REM) RS232/RS485/RS422 e ts'ehetsa hot-plug, e ts'ehetsa khokahano ea sesebelisoa sa DTE kapa DCE RS232/RS485/RS422 kanale e ka fetisa data e feto-fetohang ka mokhoa o tšoanang 0Kbps-57600Kbps sekhahla sa baud E na le ts'ebetso ea tlhahlobo ea khoutu e sa sebetseng ea pseudo, habonolo mohala o bulehileng, o ka sebelisoa. Tšireletso ea lehalima ea BER Tester Serial e fihlile IEC61000-4-5 (8/20μS) DM (Mokhoa o fapaneng): 6KV, Impedance (2 Ohm), CM (Mokhoa o Tloaelehileng): 6KV, Impedance (2 Ohm) e tloaelehileng Fana ka li-impedances tse 2: 75 Ohm ho se leka-lekane le 120 Ohm ho leka-lekana; E ka theha E1 serial converter (A) --- E1 fiber optic Modem (B) --- fiber serial Modem (C) topology AC 220V, DC-48V, DC+24V, DC Power le Polarity-Free Parameters ♦ interface ea E1 Interface Standard: lumellana le protocol G.703; Sekhahla sa Sehokelo: 2048Kbps ± 50ppm; Khoutu ea Sehokelo: HDB3; Tšitiso: 75Ω (ho se leka-lekane), 120Ω (ho leka-lekana); Mamello ea Jitter: Ho ea ka protocol G.742 le G.823 Allowed Attenuation: 0~6dBm ♦ Serial interface Standard EIA/TIA-232 RS-232 (ITU-T V.28) EIA/TIA-422 RS-422 (ITU -T V.11) EIA/TIA-485 RS-485 (ISO/IEC8284) Serial Interface RS-422: TXD+, TXD-, RXD+, RXD-, Signal Ground RS-485 4 lithapo: TXD+, TXD-, RXD+, RXD-, Signal Ground RS-485 2 lithapo: Corpond Data+(Res TX+), Lintlha-(Mongolo TX-）, Signal Ground RS-232: RXD, TXD, Signal Ground ♦ Tikoloho ya tshebetso Mocheso wa ho sebetsa: -10°C ~ 50°C Mongobo o sebetsang: 5%~95 % (ha ho condensation) Mocheso wa polokelo: -40°C ~ 80°C Mongobo oa Polokelo: 5%~95 % (ha ho condensation) Lintlha Nomoro ea Mohlala: JHA-CE1D8/R8/Q8 Tlhaloso ea Mosebetsi E1-8RS232/422/485 Converter , e fana ka li-interfaces tse tharo Ho ea ka Boikhethelo ， E sebelisoa ka bobeli , Serial port rate ho fihla ho 56.7Kbps Port Description One E1 interfaces, 8 data interface Fepelo ea matla: AC180V ~ 260V ;DC -48V;DC +24VTsebeliso ea matla: ≤10W Dimension Sehlahisoa sa boholo: Mofuta o monyenyane 216X140X31mm (WXDXH), 1.3KG / sengoathoana 19inch 1U mofuta oa 483X138X44mm (WXDXH), 2.0KG / sengoathoana Kopo Tharollo e tloaelehileng 1 Tharollo e tloaelehileng 2

Likarolo: ◊ E tsamaellana le lintlha tsa motlakase tsa 40GbE XLPPI ho IEEE 802.3ba-2010 ◊ E tsamaellana le QSFP+ SFF-8436 Specification ◊ Aggregate bandwidth ea > 40Gbps ◊ E sebetsa ho 10.3125 datha ea motlakase ea 10.3125/6 Gbps ◊ QSFP MSA e lumellana ◊ E khona ho fetisa phetiso ea 100m ho OM3 Multimode Fiber (MMF) le 150m ho OM4 MMF ◊ phepelo ea motlakase e le 'ngoe + 3.3V e sebetsang ◊ Ntle le mesebetsi ea tlhahlobo ea dijithale ◊ Mofuta oa mocheso 0 °C ho isa ho 70 °C Karolo ea RoHS ◊ E sebelisa LC e tloaelehileng Duplex fiber cable e lumellang ho sebelisoa hape ha meaho ea lithapo tse teng Likopo: ◊ 40 Gigabit Ethernet e hokahanya ◊ switch ea Datacom/Telecom & likhokahanyo tsa router ◊ Khokahano ea data le lits'ebetso tsa backplane ◊ Proprietary protocol le lits'ebetso tsa letsoalo Fiber-Optic QSFP+ Transceiver bakeng sa 40 Gigabit Ethernet Lisebelisoa. Transceiver ena ke mojule oa ts'ebetso e phahameng bakeng sa puisano e khutšoane ea data ea duplex le lits'ebetso tsa khokahano. E kopanya litselana tse 'ne tsa data tsa motlakase ka lehlakoreng le leng le le leng ho fetisetsa thapo e le 'ngoe ea LC duplex fiber optic cable. Tsela e 'ngoe le e' ngoe ea motlakase e sebetsa ho 10.3125 Gbps 'me e lumellana le sebopeho sa 40GE XLPPI. Transceiver ka hare e kopanya sebopeho sa XLPPI 4x10G ho likanale tse peli tsa motlakase tsa 20Gb / s, ho fetisetsa le ho amohela e 'ngoe le e' ngoe ka optically holim'a fiber e le 'ngoe e bonolo ea LC e sebelisa li-bi-directional optics. Sena se fella ka bandwidth e kopaneng ea 40Gbps ho thapo ea duplex ea LC. Sena se lumella ho sebelisoa hape ha LC duplex cabling infrastructure e kentsoeng bakeng sa ts'ebeliso ea 40GbE. Lihokelo tsa ho hokela ho fihla ho 100 m ho sebelisa OM3 le 150m ho sebelisa OM4 optical fiber lia tšehetsoa. Li-module tsena li etselitsoe ho sebetsa holim'a litsamaiso tsa fiber tsa multimode li sebelisa bolelele ba maqhubu a 850nm ka lehlakoreng le leng le 900nm ka lehlakoreng le leng. Sehokelo sa motlakase se sebelisa sehokelo sa 38 sa mofuta oa QSFP +. Sehokelo sa optical se sebelisa sehokelo se tloaelehileng sa LC duplex. Sets'oants'o sa Thibelo ea Transceiver • Absolute Maximum Ratings Ratings Letšoao Min. Tloaelehileng Max. Unit Storage Mocheso TS -40 +85 °C Supply Voltage VCCT, R -0.5 4 V Relative Humidity RH 0 85 % • Tikoloho e Khothalletsoang ea Ts'ebetso: Parameter Symbol Min. Tloaelehileng Max. Unit Case e sebetsang Mocheso TC 0 +70 °C Supply Voltage VCCT, R +3.13 3.3 +3.47 V Supply Current ICC 1000 mA Power Dissipation PD 3.5 W • Litšobotsi tsa Motlakase (TOP = 0 ho 70 °C, VCC = 3.4 Volts Parats 3.47 Voltage 3.47 Letshwao Min Typ Max Unit Note Data Rate per Channel - 10.3125 11.2 Gbps Power Consumption - 2.5 3.5 W Supply Current Icc 0.75 1.0 A Control I/O Voltage-High VIH 2.0 Vcc V Control I/O Voltage-Low VIL 0 0 0.7 V Inter-Channel SET SET Duration Skew 10 Rona RESETL De-assert nako 100 ms Matla ka Nako 100 ms Transmitter E le 'ngoe e Phethahetseng Matla a Matla a Matla 0.3 4 V 1 Mokhoa o Tloaelehileng Mamello ea Voltage 15 mV Transmit Input Diff Voltage VI 120 1200 mV Transmit Input Diff Impedance 1 ZINt Input 08 Dj Dependence 1 ZINt Input 08 Dj 0.1 UI Data Input Kakaretso ea Jitter TJ 0.28 UI Receiver E le 'Ngoe E Qetetsoeng ea Matla a Mamello ea Matla a Matla 0.3 4 V Rx Output Diff Voltage Vo 600 800 mV Rx Output Rise and Fall Voltage Tr/Tf 35 ps 10 Kakaretso ea Jitter Jitter DJ4 DJI Kakaretso ea Jitter UJ2 DJ Tlhokomeliso: 20～80% • Optical Parameters (TOP = 0 ho 70 °C, VCC = 3.0 ho 3.6 Volts) Parameter Symbol Min Typ Max Unit Ref. Transmitter Optical Wavelength CH1 λ 832 850 868 nm Optical Wavelength CH2 λ 882 900 918 nm RMS Spectral Width Pm 0.5 0.65 nm Karolelano ea Matla a Optical ka Channel Pavg -4 -2.5 +5.0m Extinction Ratio ER 3.5 dB Relative Intensity Noise Rin -128 dB/HZ 1 Optical Return Loss Tolerance 12 dB Receiver Optical Center Wavelength CH1 λ 882 900 918 nm Optical Center Wavelength 3 CH2 8m Recensity 3 CH2 8m Recensity 8 l 8m Recensie ka Channel R -11 dBm Maximum Input Power PMAX +0.5 dBm Reflectance Reflectance Rrx -12 dB LOS De-Assert LOSD -14 dBm LOS Assert LOSA -30 dBm LOS Hysteresis LOSH 0.5 dB Note 12dB Reflection e khethiloe ka Page02 mosebedisi. Tlhaloso e qaqileng ea memori e tlase le page00.page03 mohopolo o ka holimo ka kopo, bona tokomane ea SFF-8436. • Nako ea Soft Control le Status Functions Parameter Symbol Max Unit Conditions Initialization Time t_init 2000 ms Nako ho tloha ho motlakase ho1, hot plug kapa ho phahama ha Reset ho fihlela mojule o sebetsa ka botlalo2 Reset Init Assert Time t_reset_init 2 μs A Reset e hlahisoa ke ho fokotseha. boemo ba nako e telele ho feta bonyane ba nako ea ho letsa ha molumo o teng ho ResetL pin. Serial Bus Hardware Ready Time t_serial 2000 ms Nako ho tloha power on1 ho fihlela module e araba phetiso ea data holim'a 2-wire serial bus Monitor Data ReadyTime t_data 2000 ms Nako ho tloha power on1 ho data ha e so lokisoe, bit 0 of Byte 2, deassted and IntL asserted Seta bocha Nako ea Assert t_reset 2000 ms Nako ho tloha pheletsong e holimo ho ResetL pin ho fihlela mojule o sebetsa ka botlalo2 LPMode Assert Time ton_LPMode 100 μs Nako ho tloha ho tiisetso ea LPMode (Vin:LPMode =Vih) ho fihlela motlakase oa motlakase o kena ka tlaase ho Power Level IntL Assert Time ton_IntL 200 ms Nako ho tloha ha boemo bo hlaha ho fihlela IntL Vout:IntL = Vol IntL Deassert Nako toff_IntL 500 μs toff_IntL 500 μs Nako ho tloha ka ho hlakileng ho bala3 ts'ebetso ea folakha e amanang le eona ho fihlela Vout:IntL = Voh. Sena se kenyelletsa linako tsa sejo sa Rx LOS, Tx Fault le likotoana tse ling tsa folakha. Rx LOS Assert Nako ton_los 100 ms Nako ho tloha ho Rx LOS state ho ea ho Rx LOS bit set le IntL asserted Flag Assert Time ton_flag 200 ms Nako ho tloha ha boemo bo hlahisa folakha ho isa ho sete ea folakha e amanang le IntL e tiisitse Mask Assert Nako ton_mask 100 ms Nako ho tloha maske bit set4 ho fihlela polelo e amanang le IntL e koetsoe Mask De-assert Nako toff_mask 100 ms Nako ho tloha mask bit clear4 ho fihlela ts'ebetso e amanang le IntlL e qalella ModSelL Assert Time ton_ModSelL 100 μs Nako ho tloha ho tiisetso ea ModSelL ho fihlela mojule o arabela phetiso ea data holim'a 2-wire serial bus ModSelL Deassert Time toff_Mod0 Time toff_Mod0 Time toff. ea ModSelL ho fihlela mojule o sa arabe phetiso ya data ho feta 2-wire serial bus Power_over-ride orPower-set Assert Time ton_Pdown 100 ms Nako ho tloha P_Down bit set 4 ho fihlela mojule tshebediso ya motlakase e kena tlase Power Level Power_over-ride kapa Power-set De. -assert Nako toff_Pdown 300 ms Nako ho tloha P_Down bit cleared4 ho fihlela module e sebetsa ka botlalo3 Hlokomela: 1. Power on e hlalosoa e le hang hang ha li-voltage tsa phepelo li fihla 'me li lula li le ho kapa ho feta boleng bo boletsoeng. 2. Ho sebetsa ka botlalo ho hlalosoa e le IntL e tiisitsoeng ka lebaka la data e seng e lokisitsoe, bit 0 byte 2 de-asserted. 3. E lekantsoe ho tloha pheletsong ea oache e oelang kamora ho emisa hanyane ea transaction. 4. E lekantsoe ho tloha pheletsong ea oache e oelang kamora ho emisa hanyane ea transaction. • Pin Assignment Diagram of Host Board Connector Block Pin Numbers and Name • Pin Description Pin Logic Symbol Name/Tlhaloso Ref. 1 GND Ground 1 2 CML-I Tx2n Transmitter Inverted Data Input 3 CML-I Tx2p Transmitter Non-Inverted Data output 4 GND Ground 1 5 CML-I Tx4n Transmitter Inverted Data Output 6 CML-I Tx4p Transmitter Non-Inverted 7 Data Sebaka sa 18 LVTTL-I ModSelL Module Select 9 LVTTL-I ResetL Module Reset 10 VccRx +3.3V Power Supply Receiver 2 11 LVCMOS-I/O SCL 2-Wire Serial Interface Clock 12 LVCMOS-I/O SDA 2-Wire Serial Interface Data 13 GND14 Ground 1 CML-O Rx3p Moamoheli oa Phatlalatso ea Inverted Data Output 15 CML-O Rx3n Receiver Sephetho se sa Keneng 16 GND Ground 1 17 CML-O Rx1p Receiver Inverted Data Output 18 CML-O Rx1n Receiver Non-Inverted Data Output 19 GND Ground 1 20 GND Inverted CML Receiver CML Lintlha Sehlahisoa 22 CML-O Rx2p Moamoheli Sephetho sa data se sa Keneng 23 GND Ground 1 24 CML-O Rx4n Receiver Inverted Data Output 25 CML-O Rx4p Receiver Sehlahisoa sa Lintlha tse sa Keneng 26 GND Ground 1 TL-8 PredP LVT 1 TL-8 Modul LVT LVTTL-O IntL Interrupt 29 VccTx +3.3V Power Supply Transmitter 2 30 Vcc1 + 3.3V Power Supply 2 31 LVTTL-I LPMode Low Power Mode 32 GND Ground 1 33 CML-I Tx3p Transmitter Inverted Data Output3x300 CMLnItter3x Output T3x -Data e Inverted Output 35 GND Ground 1 36 CML-I Tx1p Transmitter Inverted Data Output 37 CML-I Tx1n Transmitter Non-Inverted Data Output 38 GND Ground 1 Lintlha: GND ke letšoao bakeng sa single le phepelo(matla) a tloaelehileng bakeng sa li-module tsa QSFP, Tsohle li tloaelehile. ka har'a mojule oa QSFP le li-voltages tsohle tsa module li boletsoe ho bokhoni bona bo boletsoeng ka tsela e 'ngoe. Hokela tsena ka ho toba ho moamoheli boto letšoao common fatše sefofane. Sehlahisoa sa Laser se koetsoe ho TDIS >2.0V kapa se butsoe, se lumelletsoe ho TDIS