Framed E1-FE interface Converter JHA-CE1fF1

Short Description:

This interface converter is based on FPGA,providing one framed E1 interface and one Ethernet interface to achieve 10/100Base-T Ethernet data transmission on the E1 channel. It is a high performance, self-learning Ethernet bridge.


Overview

Download

Framed E1-FE interface Converter JHA-CE1fF1

Overview

This interface converter is based on FPGA,providing one framed E1 interface and one Ethernet interface to achieve 10/100Base-T Ethernet data transmission on the E1 channel. It is a high performance, self-learning Ethernet bridge. This device is the extension device of Ethernet, using network (PDH/SDH/Microwave) that provide E1 channel to achieve local and remote Ethernet interconnecting with serial interfaces at a lower cost. The device has inter-set loop test function to facilitate the project launching and daily maintenance.

Product Photo

 342 (1)

Mini  Type

Features

  • Based on self -copyright  IC 
  • Can realize monitor and control of remote equipment, OAM management data did not  take up user’s timeslot and save E1 bandwidth
  • E1 supports any timeslot set, the rate is 64K-2048K
  • The local device can forced the remote device rate follow it
  • Have the function of E1 interface loop back check, avoid the converter crashed because of interface loop return;
  • Have indicator  when the device is power-off or E1 line is broken or lose signal;
  • Can set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken;
  • The Ethernet interface supports jumbo frames (2036 Bytes);
  • Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering 
  • Ethernet interface supports10M/100M, half/full duplex auto- Negotination and AUTO-MDIX(crossed line and straightly connected line self-adaptable );
  • Have Ethernet monitor self-reset function, the equipment will not dead
  • Can achieve the remote device setting any 5 mode of Ethernet and can closed the AUTO-MDIX function; 
  • Provide 2 clock types: E1 master clock and E1 line clock;
  • Have three Loop Back Mode: E1 interface Loop Back (ANA)Ethernet interface Loop Back(DIG)Command the remote
  • Ethernet interface Loop Back(REM) 
  • Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
  • Support SNMP Network Management;
  • Can realize monitor of remote equipment temperature and voltage from local equipment;  
  • Can form the structure: Ethernet E1 Bridge(A)---E1 Optical Fiber Modem(B)---Ethernet Optical Fiber Modem (C) 
  • Can form the structure: Ethernet E1 Bridge(A)---Optical Ethernet E1 Bridge (B)---Ethernet Optical Fiber Transceiver (C), can manage (B) and (C) at (A)

Parameters

♦ E1 Interface

Interface Standard: comply with protocol G.703;
Interface Rate: n*64Kbps±50ppm;
Interface Code: HDB3;

E1 Impedance: 75Ω (unbalance), 120Ω (balance);

Jitter tolerance: In accord with protocol G.742 and G.823

Allowed Attenuation: 0~6dBm

♦ Ethernet interface(10/100M)

Interface rate: 10/100 Mbps, half/full duplex auto-negotiation

Interface Standard:     Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)

MAC Address Capability: 4096

Connector:     RJ45, support Auto-MDIX

♦ Working environment

Working temperature:    -10°C ~ 50°C

Working Humidity:     5%~95 % (no condensation)

Storage temperature: -40°C ~ 80°C

Storage Humidity: 5%~95 % (no condensation)

Specifications

Model Model Number:JHA-CE1fF1
Functional Description 1channel framed E1 – FE converter N * 64k rate setting With E1 loopback detection function
Port Description One E1 interface1*FE Interface
Power Power supply: AC180V ~ 260VDC –48VDC +24VPower consumption: ≤10W
Dimension Product Size:  216X140X31mm (WXDXH)
Weight 1.1KG/piece

Application

Typical solution 1

342 (2) 342 (3) 342 (4)

Typical solution 2

342 (3)

Typical solution 3

342 (2)


  • Previous:
  • Next:

  • Write your message here and send it to us