L3 Managed PoE Switch 4 Port with 2 1G/2.5G/10G SFP Slot | JHA-MT2G05P-L3
Introduction
JHA-MT2G05P-L3 PoE Switches support 4 100/1000/2500TX PoE/PoE+ and 1 100/1000/2500TX RJ45 and 2 100/1000/2500/10000X SFP/SFP+ Slot, built-in power supply, support QoS, widely used in Ethernet access applications such as small and medium-sized enterprises, Smart cities, security monitoring, and schools.
PoE switch is a kind of network switch that applies Power over Ethernet technology, which transmits both power and data to IP-based terminals (such as IP phones, wireless access APs, IP cameras) through a single twisted-pair cable.
Devices that support PoE can be power sourcing equipment (PSE), powered devices (PD), or sometimes both, the device that transmits power is a PSE, and the device that is powered is a PD. Most PSEs are either network switches or PoE injectors.
PoE technology can automatically detect power consumption of the powered devices and provide the required amount of power to maximize the use of power resources and save costs. On the other hand, non-PoE device intelligently detects no power and only transmits data.
PoE Switches do not need to run additional power cord to connect to the devices, saving the costs of power cables, power outlets, and infrastructure equipment required for electrical installation. PoE powered devices can be easily moved to locations where there is no power outlet, such as wireless network repeaters or IP security cameras because they are usually installed on high walls or ceilings away from power socket.
Power over Ethernet (POE) technology transmits 100M or 1000Mbps data and power budget of 15W, 30W to the devices through Cat5e and Cat6 Ethernet cables at a maximum distance of 100 meters.
Features
Specifications
|
Managed PoE Switch Hardware Parameters |
|
|
Fixed Port |
4*100/1000/2500M RJ45 PoE 1*100/1000/2500M RJ45 2*100/1000/2500/10000M SFP |
|
PoE Port |
1-4 port supports PoE |
|
Console Port |
1*console port |
|
Reset |
1 |
|
Network Protocol |
IEEE 802.3 IEEE 802.3u 100BASE-TX IEEE 802.3ab1000BASE-T IEEE 802.3x IEEE 802.3z 1000BASE-X IEEE 802.3af/at IEEE 802.3ad IEEE 802.3q 、IEEE 802.3q/p IEEE 802.1w、IEEE 802.1d 、IEEE 802.1S STP(Spanning Tree Protocol) RSTP/MSTP( Rapid Spanning Tree Protocol) EPPS ring network protocol EAPS ring network protocol |
|
Port Specification |
10/100/1000/2500BaseT（X）Auto |
|
Transmission Mode |
Store and Forward(full wirespeed) |
|
Bandwidth |
512Gbps |
|
Packet Forwarding |
89.28Mpps |
|
MAC Address |
32K |
|
Buffer |
16M |
|
Transmission Distance |
10BASE-T ： Cat3,4,5 UTP(≤250 meter) 100BASE-TX ： Cat5 or later UTP(≤150 meter) 1000BASE-TX ： Cat6 or later UTP(≤150 meter) 2500BASE-TX ： Cat6 or later UTP(≤100 meter) SFP: Support 100M/1G/2.5G/10G SM,DM SFP modules,MAX transmission distance≤120km |
|
FLASH |
512M |
|
RAM |
512M |
|
Watt |
≤65W |
|
LED Indicator |
PWR:Power LED SYS:(System LED) PoE: Orange PoE LED |
|
Power |
External power DC52V 1.25A (AC：100-240Vac 50-60Hz 0.9A MAX: 71W) |
|
Operating Temperature/Humidity |
-10～+55°C；5%～90% RH Non coagulation |
|
Storage Temperature/Humidity |
-40～+75°C；5%～95% RH Non coagulation |
|
Product size/Packing size（L*W*H） |
220mm*112mm*30mm 265mm*220mm*68mm |
|
N.W/G.W（kg） |
0.8kg/1.3kg |
|
Installation |
Desktop(optional wall+machine hanger parts) |
|
Lightning protection level |
6KV 8/20us； IP30 |
|
Features |
L3 Switch |
|
Port |
|
|
Number of Fiber 10G ports |
Maximum 4 ports |
|
Port Shutdown |
Support |
|
Port Speed |
Support autonegotiate, full-1000, full-100, half-100, full-10, half-10 |
|
Flow Control |
support full-duplex IEEE 802.3x, half-duplex back pressure |
|
Storm Control |
Supports rate limit for broadcast, multicast, and DLF packets |
|
Storm Constrain |
Support the detection of broadcast packets, multicast packets, or unicast packets on the port, shutdown the port if the rate is over the threshold. |
|
Port Mirror |
Support |
|
Port Rate Limit |
Support port ingress and egress rate limit |
|
Link Aggregation |
Support manual link aggregation Support LACP dynamic link aggregation Supports up to 32 aggregation groups, each group up to 8 ports Support source MAC, destination MAC, source destination MAC, source IP, destination IP, source destination IP routing strategy |
|
Port Isolate |
Support |
|
Jumbo Frame |
Support up to 16KB packet |
|
Redundant Port |
Support |
|
The DDM of fiber ports |
Support |
|
MAC |
|
|
MAC Table Capacity |
16K |
|
MAC Table Management |
Support |
|
Forwarding mode |
Support IVL forwarding mode |
|
Static MAC Address |
Support |
|
MAC Address Binding |
Support |
|
MAC Address Filtering |
Support |
|
MAC Learning Control |
Control the MAC learning based on port |
|
VLAN |
|
|
Number of VLANs |
4K |
|
802.1q-based VLAN |
Support |
|
MAC-based VLAN |
Support |
|
IP-based VLAN |
Support |
|
Protocol-based VLAN |
Support |
|
PVLAN |
Support |
|
Voice VLAN |
Support |
|
VLAN Mapping |
Support 1:1 mapping |
|
QinQ |
Support basic QinQ Support flexible QinQ |
|
Reliability |
|
|
Spanning Tree Protocol |
Support STP/RSTP/MSTP |
|
Port Loop Detection |
Support |
|
EAPS |
Support RFC3619 |
|
ERPS |
Support G.8032/Y.1344 |
|
LLDP |
Support LLDP & LLDP-MED |
|
UDLD |
Fully compatible with CISCO’s UDLD protocol |
|
VLLP (VRRP Layer-2 Loop Protection) |
Support, Only used with VRRP |
|
L3 |
|
|
ARP |
Support static and dynamic ARP |
|
Static Route |
Support static route based on IPv4 and IPv6 |
|
VLAN Interface |
Support 32 VLAN interfaces |
|
RIP |
Support RIP v1/v2 & IPv6 RIPng |
|
OSPF |
Support OSPFv2 & IPv6 OSPFv3 |
|
BGP |
Support BGP4 & IPv6 BGP4+ |
|
Policy Route |
Support |
|
VRRP |
Support |
|
Multicast |
|
|
Static Multicast MAC Address |
Support |
|
IGMP SNOOPING |
Support IGMP SNOOPING v1/v2/v3 Support IGMP Querier Support IGMP SNOOPING Filter |
|
MVR |
Support |
|
GMRP |
Support |
|
IGMP |
Support IGMP v1/v2/v3 |
|
PIM-SM |
Support |
|
ACL |
|
|
Standard IP-based ACL |
Support |
|
Extended IP based ACL |
Support |
|
MAC IP-based ACL |
Support |
|
MAC ARP-based ACL |
Support |
|
ACL Port Filtering |
Support |
|
Time-based ACL |
Support |
|
QoS |
|
|
Port Queue Number |
8 |
|
Port Queue Scheduling Mode |
Support WRR，RR，WDRR，SP |
|
Port-based Classification |
Support |
|
802.1p-based Classification |
Support |
|
DSCP-based Classification |
Support |
|
ACL-based Classification |
Support |
|
QoS Policy |
Support packets mapping to queue Support COS or DSCP Remarking Support rate limits of data flow Support data flow statistics Support mirroring of data flow |
|
DHCP |
|
|
DHCP Client |
Support |
|
DHCP Snooping |
Support |
|
DHCP Relay |
Support |
|
DHCP Server |
Support |
|
DHCP option 82 |
Support |
|
Management |
|
|
CLI Management |
Support Console, Telnet and SSH Support multiple TELNET connections based on IPv4 and IPv6 Support multiple SSH connections based on IPv4 and IPv6 |
|
WEB Management |
Support HTTP based on IPv4 and IPv6 Support HTTPS based on IPv4 and IPv6 |
|
SNMP Management |
Support SNMP v1, v2c, v3 Support SNMP TRAP Support lots of standard and private MIBs Support SNMP and TRAP based on IPv4 and IPv6 |
|
User Management |
Support multiple user management |
|
TACACS+ |
support switch authentication via TACACS+ server remote username and password Support password encryption in PAP and CHAP mode Support TACACS+ server to authorize the switch’s commands Support TACACS+ based on IPv4 and IPv6 |
|
Log Management |
Support local log management Support SYSLOG |
|
RMON |
Support RMON 1, 2, 3 and 9 groups |
|
Cluster Management |
Support NDP Support NTDP Support manual and automatic joining of cluster groups Support cluster unified management |
|
Configuration File |
Support uploading and downloading configuration file Support TFTP transmission based IPv4 and IPv6 |
|
Upgrade software |
Support TFTP transmission based IPv4 and IPv6 |
|
Clock Management |
Support local clock management Support SNTP |
|
Security |
|
|
Switch Management Security |
Support enabling and disabling TELNET、SSH、HTTP、HTTPS and SNMP services Support TELNET、SSH、HTTP、HTTPS and SNMP services to bind to standard IP ACLs Support for limiting the number of TELNET and SSH connections |
|
CPU Protection |
The switch’s own security protection prevents large data streams from attacking the switch itself. |
|
AAA |
Support 802.1x Support RADIUS Supports authentication, authorization, and accounting through RADIUS server Support port-based and MAC-based 802.1x Support 802.1x guest VLAN |
|
IP MAC Binding |
Support static configuration of IP, MAC and port binding |
|
DHCP SNOOPING |
Support dynamic ARP binding to prevent ARP spoofing Support dynamic IP, MAC and port binding Support fixed port to connect to DHCP server to prevent private connection to DHCP server |
|
Prevent ARP Spoofing |
Support manually configuring MAC ARP-based ACL rules to prevent ARP spoofing. Support the DHCP SNOOPING function. During the process of obtaining an IP address by DHCP, the switch dynamically binds ARP to the port to prevent ARP spoofing. |
|
POE |
|
|
Switch Control |
Support POE powering of ports on and off |
|
Power Control |
Support setting total power |
|
Other Advanced Features |
Support POE scheduling policy and PD online query, etc. |
|
IPv6 |
|
|
IPv4/IPv6 Dual Protocol Stack |
Support |
|
IPv6 Address |
Support manual address configuration and stateless address auto-configuration |
|
IPv6 Neighbor Discovery
|
Support |
|
ICMPv6 |
Support |
|
IPv6 Path MTU Discovery |
Support |
|
Debugging |
|
|
PING |
Support |
|
PING6 |
Support |
|
TRACEROUTE |
Support |
|
TELNET Client |
Support TELNET client based IPv4 and IPv6 |
|
SSH Client |
Support SSH client based IPv4 and IPv6 |
Order Information
|
Model NO. |
Description |
|
JHA-MT2G05P-L3 |
L3 managed PoE switch, 4-port 100/1000/2500M PoE/PoE+ and 1-port 100/1000/2500M RJ45 and 2-port 100/1000/2500/10000M SFP/SFP+ Slot,built in power supply |
